Reference pages

Saturday, December 6, 2014

Modeling an SP Class O-50-9 tank car

One of the distinctive SP tank car classes was O-50-9. It was the first with a truly “SP standard” tank, in terms of proportions. Southern Pacific had been buying tank cars of 12,500-gallon capacity for some years, but designs varied, up through Class O-50-8. But classes O-50-9 through -13 all had the same tank proportions, which in HO scale is exactly provided by the Athearn tank car.
     One key in modeling Class O-50-9 is the availability of a good detail part for the elbow safety valve, actually a double safety valve in one elbow, characteristic of this class. Later classes all used dome-top instead of elbow mounting for safety valves. The recent elbow valve from Owl Mountain Models solves this problem. This is Part No. 1002. You can purchase it on their web site, at: http://owlmtmodels.com/ , but unfortunately the website does not yet include photos of parts.
     The goal, then, is to model a car like the pair of prototype photos below, showing the same car of Class O-50-9 from each side. Note that there is a dome walk only on one side (the left side, as seen from the B end), and the elbow safety valve arrangement (toward the B end) is evident too, as are the prominent circumferential rivet rows. (SP photo, courtesy Stanford University Libraries)


     So to set about building a tank of this class, I began, as usual with an Athearn tank car kit. I will not go into great detail about most of the changes to be made, because there is already a detailed description of what is needed, in my prior post at: http://modelingthesp.blogspot.com/2011/05/modeling-sp-tank-cars.html . That post was followed up with a few additional details. These included construction of new handrails, since one dome walk is removed (see it at: http://modelingthesp.blogspot.com/2011/06/modeling-sp-tank-cars-2-handrails.html ); how to model the circumferential rivet joints for some classes (that would be for classes O-50-9 and -10), which is at: http://modelingthesp.blogspot.com/2011/06/modeling-sp-tank-cars-3-tank-sheets.html ; part numbers if you want to order Athearn parts to add to a kit (since one kit does not have all you need), which was described in this post: http://modelingthesp.blogspot.com/2011/08/modeling-sp-tank-cars-update.html ; specifics about use of Archer rivets and underframe detailing, in the post at: http://modelingthesp.blogspot.com/2012/10/modeling-sp-tank-cars-4-circumferential.html ; and the Jerry Glow decals, for which I did artwork: http://modelingthesp.blogspot.com/2011/05/sp-tank-car-decals.html .
     I began with a plain vanilla tank car, and removed the extraneous double rivet rows on either side of the dome, on the upper tank as well as on the bottom sheet (these should not be on a single-compartment car), and removed the dome-top safety valves, manway cover, dome grab irons, and the rivet row around the top of the dome. Here is an in-progress photo at this point.


Small recommendation: choose a light-colored car as a starting point if you can, because it is much easier to see what you are doing. This will be especially helpful when the addition of Archer rivets comes along. Of course you can always spray on a “witness coat” of light gray primer, or any other light color.
     Next came removal of one dome walkway, of tank-end molded grab irons which will be replaced with wire, and adding the dome-height correction (see my first post, cited above, for specifics on the overall method). And finally, the top rivet seam must be removed, while preserving the hold-down bands, because I am modeling a car with circumferential seams on the upper tank. For tasks like removal of that rivet seam, or the grab iron removal, I always use a brand-new X-acto chisel blade.
     Here is the same car body, a little farther along, shown from the side with the removed dome walk. The dome top never fits perfectly, and some Squadron Green putty is applied to correct that. But all major things needing to be removed from the tank body are gone, and raising the dome-top means that from here on in, it will all be about adding things.


Note that the middle handrail support from the original trio on each side of the car center has been removed, as the added circumferential tank sheet will go there. The offending single safety valve has been removed from the dome top also.
     So with the completion of the “removal phase” of work on this model, I am ready for the next phase, involving the addition of new parts, especially the circumferential rivets.
Tony Thompson

3 comments:

  1. Very interesting build and would like to have one or two but please correct me if I'm wrong. Didn't Jerry Glow go out of business a few months back? Really would like to be wrong since I have much need for his products.

    George

    ReplyDelete
  2. That's correct, George, Jerry has closed down his decal business. I have been told that efforts are being made to purchase the artwork so that some or all of the decals can be made available again, but have not heard that from Jerry, I hope to talk to him at Cocoa Beach next month and find out more.
    Tony Thompson

    ReplyDelete
  3. Great work! Hope that something can be done to save the art work. Great decals. See you there.

    George Corral

    ReplyDelete