Tank car “dome” platforms, Part 4

In the previous post in this series, I showed both a prototype photo, and a model under construction, for an insulated, pressurized tank car (ICC 105) for Brea Chemicals of Los Angeles. (You can find that post at this link: http://modelingthesp.blogspot.com/2015/06/more-on-tank-car-dome-platforms-part-3.html .) One part of the project, which ties it to previous modifications I have reported for the Athearn “chemical” tank car, was the use of part of the Atlas platform part, their no. 9170013, to make the walkway alongside the valve bonnet (not an expansion dome, but nevertheless sometimes called a dome).
     At the point I stopped my modeling description in the previous post (link provided above), the bonnet and walkways had been added and primed. Now I needed to add ladders which reached all the way to the upper walks, not merely to the level of the tank handrail, as Athearn provides. Luckily in some recent Athearn “chemical” tank cars, the full-height ladders are included, so I harvested a pair of them for use on this model. They are stamped metal. I simply re-bent them slightly to reach my walkways. In the original white color, they can be seen clearly.

But as was evident in the prototype photo in the previous post (link given above), the tank handrails and ladders were black on the Brea cars, though the walkway was the same silver or silver-gray as the rest of the tank. I handpainted the model that way, as you see here.

     With trucks attached (semi-scale-tread width wheelsets added) and Kadee #158 couplers installed, the model was ready to weather. I wanted to do this in two steps. First, I oversprayed with Dullcote, and weathered the entire car with my usual acrylic tube paints, in wash form; for more on that, you can look at my Reference Pages on weathering, linked through the list at upper right of the blog page. This turned out pretty well. Here’s the car being switched at Shumala at this point.

     The second process I wanted to try was something I had watched Richard Hendrickson do, but had not tried myself. The idea is to mix a really dilute dirty black in plenty of solvent, so that airbrushing this mix from above the model just shadows the top surfaces. Let it dry a few seconds, and decide whether it needs another pass; repeat until satisfied. This technique makes a really nice representation of that “dirt from above” look, getting that area dirtier than the sides. This is especially effective on light-colored cars like this tank car. But my photos do not differ much from what is shown above, so for now I will leave the Brea tank behind. If I have a car which shows the “dirt from above” look well, I will post it later.
Tony Thompson

A fishing boat for my Santa Rosalia waterfront

On my fictional SP branch, I imagine that the track ends at a town called Santa Rosalia, located at the mouth of the Santa Maria River, and that a few fishing boats work out of there. Accordingly, it would be a nice feature to have such a boat moored at a dock. I have already said a little about my waterfront ideas for Santa Rosalia in a prior post (you can read that initial post at: http://modelingthesp.blogspot.com/2014/07/constructing-santa-rosalia-waters-edge.html ), and more recently showed my progress in modeling along the new waterfront ( http://modelingthesp.blogspot.com/2015/06/santa-rosalia-waters-edge-part-2.html ). A local fishery in turn could support a cannery (though probably not the shipping of much fresh fish). I have already gone ahead and created a model cannery, as described in an earlier post (see it at: http://modelingthesp.blogspot.com/2015/05/kitbashing-santa-rosalia-cannery.html ).
     But if there is to be a fishing boat modeled, the first question a person might ask (and I would say, ought to ask), is what kind of small fishing boats were or are used in this area? As it happens, I found a photo some time ago which clearly shows several such boats, in an image supplied by the Morro Bay (California) Visitor’s Bureau. It of course emphasizes a vivid sunset and the monumental Morro Rock, but that fishing boat in the center foreground is a clear example to work from. Morro Bay is just a few miles up the coast from my supposed location of Santa Rosalia.

     Is Morro Bay relevant? I have spent some time with a very interesting and topical report about the fisheries of central California, entitled “Commercial fishing grounds and their relative importance off the Central Coast of California,” submitted in response to the California Marine Life Protection Act, with principal author Astrid Scholz, then of Ecotrust (it’s 40 pages and is available at the website of the California Department of Fish and Game: http://www.dfg.ca.gov/mlpa/pdfs/agenda_workshop041807_report.pdf ). This 2006 report clearly shows an important fishing ground between Point Buchon on the north, and points Sal and Purissima on the south, with the mouth of the Santa Maria River right in the middle. So the Morro Bay boat shown above would work in the same fishery as would my purported Santa Rosalia boat.
     Other California fishery studies contain fishing boat photos, broadly similar to the one shown above. Here is one example, and like the photo above, the cabin is fairly long.

    Here is another image, a boat with a shorter cabin and a different rig, with a net reel amidships. Naturally there are a wide range of boat details, even in this one fishery.

    I have long admired the fine models of boats offered by Frenchman River Model Works, and seemed to remember that they offer a small boat generally like this. And indeed they do, their kit no. 81. You can see it on their web site: http://www.frenchmanriver.com/Pages/HO/Boats/fishing/fishing.html . I was sufficiently impressed to go ahead and order the kit. The cabin is shorter than many Central California boats, and I could change the cabin in the direction of the Morro Bay boat shown above, but with so many variations among individual boats, I don’t think it will be necessary.
     A couple of days after I placed the order, the kit showed up via Priority Mail, which is excellent service. The kit can be built two ways (cabin forward or cabin aft), as this flyer shows (you can click to enlarge).

As visible in the prototype photos at the top of this post and in other observations, the “cabin forward” orientation, left photo in the model images above, should be my choice.
     I opened up the kit, and immediately found that the parts are very nice, major parts cast in a brown resin, accompanied by some white metal details, all with little flash and fitting well together. I proceeded to put together the basic elements, as you see here, so I could use the model to help me proportion my waterfront elements.

The basic hatches, body details, and cabin are shown unpainted. I am considering  perhaps raising the profile of the bow, after looking at the two California prototype photos above, but haven’t decided. Then, when more details are attached, the plan is to airbrush white or light gray as a base coat. I will show addition of details, along with painting, in a future post.
Tony Thompson

Bay Area Prototype Modelers 2015

On June 20, the annual Bay Area Prototype Modelers (BAPM) meet was held in the multi-purpose room of St. David’s Church in Richmond, California. An all-day affair, the large room with tables for model display was supplemented with a clinic room in which several talks were given. Even though it was a very nice, sunny day outside, about 100 modelers showed up for a pleasant day of viewing and discussing models. Most years, I attend this meet and always enjoy it. The 2012 meet was covered in a prior blog post (you can see it at this link: http://modelingthesp.blogspot.com/2012/06/bapm-bay-area-prototype-modelers-2.html ).
     One of the most interesting displays was presented by Robert Bowdidge, showing how he has produced several SP cars for which there is no commercial source. These included the CS-35A flat car, the F-50-4 flat car, and the W-50-3 Hart convertible ballast car. All were made with a home 3-D printer. The photo below shows his display of completed cars, and he also showed a partially complete car so that the printing process could be appreciated. I tried to take close-up photos of details and did not get very good results, but the models certainly are superbly detailed.

     One of the most striking displays of freight cars at the meet was the group of weathered and graffiti-ed reefers by Tim Keohane. Here is just one example.

     Rickey T. Hall brought quite a few specially-painted locomotives, all beautifully done, and I was especially struck with this group of Bicentennial paint schemes for Santa Fe, Southern Pacific, and Western Pacific.

     Paul Chandler was at the meet, and brought his completely scratchbuilt Burro crane, which is motorized. The photo probably does not do justice to the outstanding quality of detail on this model.

     It is always interesting to see younger modelers at these meets, particularly when they too have brought excellent models. Jonathan Izen was one of those at this meet, and brought two really nice models of Richmond Pacific motive power (from the roof of the building we were in, you could probably see the RP’s trackage). This SW1200 was formerly MoPac 1268. Even the cab-side logo was crisp and readable.

     Nearby was another outstanding group of models, these by Henry Baez. Among my favorites in this group was the flat car loads. In this photo (you can click to enlarge), the hold-down clamps are beautifully modeled.

     As I often do, I brought an entire SP train of 15 freight cars, pulled by a Consolidation and trailed by a cupola caboose. Here is an overview of it.

     I always enjoy this kind of RPM meet, because there is just an amazing amount of conversation among the different tables, modelers asking things like “how did you do that” or “what’s the prototype” or “is it a kitbash” and so on. Looking around the room, you can watch everyone appreciating what they see, and in most cases learning a few things at the same time. As hobby experiences go, it is one of the most positive ones I know of.
Tony Thompson

More on tank car “dome” platforms, Part 3

I have posted a description of my efforts to create a properly sized platform on an Athearn high-pressure tank car, surrounding the valve bonnet (it is sometimes called a “dome” but is not an expansion dome). That post can be found at: http://modelingthesp.blogspot.com/2015/05/another-approach-to-tank-car-platforms.html . My changes used an Atlas tank car part. In this post, I show another way to improve an Athearn “chemical” tank car, also using the same Atlas part.
     The part is Atlas no. 9170013, and to repeat a photo from the previous post, looks like this.

In the previous post, I used the leftmost part of this molding (the entire left handrail  plus the space between the two handrails), and mated it with the same part of a second molding (reversed) to make a full platform with handrails. (If this description is confusing, please see the post cited at the top of this post, as it shows the process.) What was left over was the righthand side of the Atlas part in the photo above (that is, the entire handrail section at right). I use the grid walkway part of that section in the present post as raw material for a “dome” walk.
     But before I begin with the modeling, let me show what prototype I am aiming at. It is a General American car leased to Brea Chemicals, which was part of the Chemicals Division of Union Oil Company, with a plant manufacturing ammonia and other fertilizer constituents. The plant was at Brea, California, thus the name. This photo is from Richard Hendrickson’s collection, but I don’t know photographer, date, or location.

Note that the car has only a short walkway alongside the valve bonnet (a photo of a different Brea car shows a longer walkway), and has a ladder reaching all the way up to the walkway. It’s possible that the ladder was only on this side, but by the time this car was built in 1948, the usual practice was to have ladders and walks on both sides. It’s evident that the tank handrail and ladder are painted black.
     Here is an Athearn kit (custom decorated) that I have had for some time, with the bonnet sawn off and the site filed flat, some paint touch-up, and addition of the bottom part of the Frank Hodina bonnet (see prior post). Also visible are two pieces of white styrene, which are pieces of scale 4 x 4-inch strip, cut in half the long way, diagonally (making a triangular cross-section), then glued down on the wide side, so that the upper surface of the strip is close to horizontal.

The purpose of these little white pieces is to support the walkways which go alongside the bonnet.
     The two walkways are cut from the unused part of the Atlas platform shown at the top of this post. Here they are, applied atop those styrene strips, and with the Hodina bonnet completed.

     During the work shown above, I was also fixing the Athearn underframe, in the way that I normally do. Removing the three sets of bottom outlet details, drilling the coupler pocket post and cover so they could be tapped 2-56, then cutting off the pocket covers so they become separate pieces, are all essential here. Also, the vertical-wheel handbrake arrangement furnished by Athearn, a rare prototype arrangement for tank cars, is removed and a brake staff of 0.019-inch brass wire installed. I usually add a Tichy tank car brake wheel, as I did here.
     The Athearn bottom sheet, designed for their three-compartment car, also needs cleaning up. All rivets on this part should be removed, though I sometimes leave the ones on the center anchor. All other rivets definitely go. The bottom sheet in my custom-deocrated kit is black, and the prototype photo above shows that it should be black, though the prototype one is located very low on the tank. I chose not to try and reproduce that location.
     I could now assemble bottom sheet to tank, and underframe to tank body, and did so. Here is the model at this point, with primer on the bonnet and walkways. You can just see the brake wheel on the near end (click to enlarge if you wish).

I will show how I handled the ladders, and will complete the rest of the model, including weathering, in an upcoming post.
Tony Thompson

The East Shumala stock pen, Part 2

In Part 1 of this thread, I talked about stock pens in a general way, and provided some citations to sources of information about the livestock business. I also said a little about the starting point for my stock facility, the old Associated Hobby (AHM) kit. You can read that previous post at this link: http://modelingthesp.blogspot.com/2015/03/a-stock-pen-for-east-shumala.html .
     As I stated in the first post, I wanted to expand the size of the facility by adding another pen, which meant building some additional fencing. I also needed to correct the failure of some kit parts to have horizontal boards on both sides, which the prototype did for any fencing which had animal movement on both sides. As part of the facility, I also wanted to provide a water supply and an office.
     The fencing part of the problem is fairly easy. Using Evergreen styrene, I added horizontal boards of scale 2 x 8-inch strip, and posts of scale 4 x 4-inch strip. Here, from top to bottom, are an unmodified original AHM piece (top), two of the new fencing units (middle), and an AHM section with doubled side boards added (bottom).

Once all fence modifications or new construction was complete, both sides of all parts were airbrushed with Star Brand “Seasoned Brown Wood” color, STR-11.
     The AHM kit included a “ground”piece to which fences and buildings could be attached. I began by painting it with a mixture of acrylic tube paints, Raw Umber and Yellow Ochre. Then I assembled the fencing to the base by following slots in the base, and gluing my fence segments into the slots.
     With this part of the job completed, I decided to see how it looks on the layout, even though my expansion section wasn’t finished yet. Here is a photo.

That’s the Phelan & Taylor packing house in the background, and Pismo Dunes Road in the foreground.
     In the photo above, you see additional structures, in addition to the kit fences. Accessory buildings include the water tank, which was probably no longer water-filled once town water was available, modeled as a familiar California structure, a tankhouse. In two previous posts, I described the background and modeling of these structures, starting with this link: http://modelingthesp.blogspot.com/2015/04/building-california-tankhouse.html . After that introductory post, I completed the modeling, at: http://modelingthesp.blogspot.com/2015/05/building-california-tankhouse-part-2.html .

     Also visible in the photo above, at the right of the pens, is an office, a small brick structure left over from another kit. It is about the right size, but does not seem to me to look right as a small office for this stock facility. I would expect such an office to be a simple frame building, and one with a lesser roof pitch, so will have to put together such a structure. This is of course quite easy with styrene sheet and commercial windows. I will show it in the following post.
     I have also started work on my expansion pen, which will be located at the right of the kit pens as seen in the photo above. I began with a piece of 0.040-inch thick styrene about the same size as the kit base, and added a water trough to match those in the AHM kit. This additional base piece will support the added fencing for the third (expansion) pen. The new base was painted with the same acrylic colors, then fencing was applied. I will continue with this model in a future post.

Tony Thompson

Waybills, Part 41: overlay bills

I have described in previous posts the idea of “overlay” or partial waybills, which permit different loads to be assigned to a particular car without a new waybill. You can read the original post’s discussion on that idea at this link: http://modelingthesp.blogspot.com/2011/08/waybills-10.html . I developed the idea further for use with Empty Car Bills, which adds further flexibility to car handling and movement, in a subsequent post, which is here: http://modelingthesp.blogspot.com/2012/02/waybills-19-confiscation.html . I have also called these “short” bills in some posts, if you want to use the search box to find further discussion.
     If these ideas have been previously described, why am I bringing them up again? The main reason is that until recently, I had not seriously implemented these ideas for my own layout. The examples in the posts cited above are for Otis McGee’s layout, which differs in having largely bridge traffic and relatively little on-line industrial switching. I wanted to see how well they would work on my own layout, which is entirely dominated by switching.
     The basic idea, for me or for Otis, is simple, but it has some subtle points, along with some obvious things to watch. Since the idea is to use a full waybill as backing, and that waybill shows the originating railroad along with car initials and number, the overlay bill works much the best for loads originating on the home railroad of the layout, in my case Southern Pacific. Moreover, it should be obvious that this idea can only be applied to free-running cars like box cars, or to cars which always have the same purpose, like refrigerator cars. Here is an example. This way, a particular car does not always head off to the same destination; and when there are multiple refrigerated shippers in one town, as in my layout location of Ballard, a particular car will not even always be sent to the same shipper.

     The same can obviously apply to box cars, as in these two outbound loads from Pacific Chemical Repackaging in Ballard:

And here again, the empty box car arriving in Ballard can be directed to any industry which loads such cars outbound.
     This same idea can work for other free-running cars like gondolas and flat cars, though I don’t have much in the way of industries shipping in those cars. Lastly, if there is more than one originating industry on an off-line railroad (the Northern Pacific, let’s say) for a particular car type like box cars, this method can even work (in my case) for non-SP waybills. Here’s an example from the Pennsylvania Railroad, of box cars headed to two different Ballard industries:

     This enables a particular car to take different inbound jobs as well as different outbound jobs, a helpful way to avoid the same problem mentioned above, the same car always with the same load or job. And it may be obvious, but in case it isn’t, let me say that numbers of these “overlay” bills can be made up for a single shipper, representing multiple shipment options. All four of my packing houses have ten or so overlay bills each. And of course I have lots of PFE and other reefer waybills with which these overlays can be paired.
     Incidentally, let me make the further point in passing, that many modelers, devising a waybill inbound to an SP location from the PRR, would automatically choose a PRR box car, or an eastern box car. In fact, under car service rules, the PRR yardmaster would be attempting to find SP or at least Western railroads for his load to California. Of course eastern or PRR cars might get this load, too, but not every time.
     These ideas clearly are not practical for foreign railroads which aren’t very big shippers to my layout area, or don’t load all the same kinds of cars, nor of course can they work for specially equipped cars in most cases. But they do work for some large groups of cars, as I showed above. I am happy to see them working on my Santa Rosalia Branch layout.
Tony Thompson

Richard Hendrickson’s lumber loads

Awhile back, I showed photos of several dramatic freight car loads built by Richard Hendrickson, loads which required two or more cars to transport (see it at: http://modelingthesp.blogspot.com/2015/03/richard-hendricksons-multi-car-loads.html ). Richard was obviously intrigued by those kinds of loads and thus built a number of them. He also was intrigued by lumber loads, and built several different kinds, which I want to show in this post. (You can click on any of these images to enlarge them.)
     After packing up all of Richard’s freight cars, I photographed almost every one, before distributing most of them to his many friends. Thus I have the photos to show, even of cars I no longer have. One thing to realize: he almost always glued loads onto or into cars, partly so he could freely model tie-down or other attachment methods, without having to worry about removability. All the ones shown here are glued on. For his diorama-style layout design, there was to have been little or no switching, so there was no need for removable loads.
     I will begin with one of his oldest models of a lumber load, a converted Athearn 40-foot flat car with upgraded details. It is lettered for Great Northern 69534, the prototype for which is indeed quite similar to the Athearn model.

The lumber load here is a triple stack, a common practice which is seen in prototype photos. The load is entirely built board-by-board, though it is hollow.
     A similar load in terms of lumber size is this one, on a Tichy 40-foot flat car. The Nashville, Chattanooga & St. Louis is one of the prototypes for which the Tichy car is an almost exact match, thus this choice of NC&StL 70153 lettering.

This load also is board-by-board, and is hollow.
     Sometimes prototype photos do show much larger timbers being moved on flat cars, and Richard modeled an example, in this case using one of the WestRail models from his own company. It is a 53-foot, 6-inch car, lettered Northern Pacific 62148.

     Another interesting variation is creosoted lumber, such as bridge timbers or other kinds of uses, modeled here on an SL-SF flat car (modified from an Athearn 40-foot model). Lettering is SL-SF 95470. In this case, Richard applied cast brass stake pockets on the car to replace the rather oversize pockets molded by Athearn, and as you can see, was able to represent side stakes extending through these pockets. These same pockets were provided in the WestRail flat car kits.

     Finally, not really lumber but certainly forest products, is this striking load of creosoted poles, again on one of Richard’s own WestRail models. This too is  a 53-foot, 6-inch car, numbered UP 57255. Here, he chose to use very fine wire for the cross-ties on the stakes, something often seen on the prototype but rarely modeled. The poles are sanded-down chopsticks.

     The variety of these loads, and the fine modeling achieved to represent them, including the accurate load securements, are another testimony to Richard Hendrickson’s skills. They have given me modeling ideas, and I hope you may have a few also.
Tony Thompson